IR2UAZ-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object IR2UAZ-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Batt*	Value2*	Value3*	Value4*	Value5*
1784662724	12.7 Volt	0	0	0	0
1784661524	12.7 Volt	0	0	0	0
1784660323	12.7 Volt	0	0	0	0
1784659123	12.7 Volt	0	0	0	0
1784657923	12.8 Volt	0	0	0	0
1784656723	12.9 Volt	0	0	0	0
1784655522	13.4 Volt	0	0	0	0
1784654322	14 Volt	0	0	0	0
1784653122	14.2 Volt	0	0	0	0
1784651921	13.6 Volt	0	0	0	0
1784650721	13.5 Volt	0	0	0	0
1784649520	13 Volt	0	0	0	0
1784648320	13.3 Volt	0	0	0	0
1784647120	13.8 Volt	0	0	0	0
1784645920	13.7 Volt	0	0	0	0
1784644719	13.8 Volt	0	0	0	0
1784643520	13.5 Volt	0	0	0	0
1784642319	13.8 Volt	0	0	0	0
1784641118	13.8 Volt	0	0	0	0
1784639918	13.8 Volt	0	0	0	0
1784638717	13.8 Volt	0	0	0	0
1784637517	13.7 Volt	0	0	0	0
1784636317	13.8 Volt	0	0	0	0
1784635117	13.6 Volt	0	0	0	0
1784633916	14.3 Volt	0	0	0	0

*Used Equation Coefficients:

Batt: 0, 0.1, 0

Value2: 0, 1, 0

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)