SA7NOA-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SA7NOA-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	V_Bat*
1789951034	308 Count	860 Count	4.07 VDC
1789950131	307 Count	856 Count	4.07 VDC
1789949227	306 Count	853 Count	4.07 VDC
1789948323	305 Count	849 Count	4.07 VDC
1789947420	304 Count	847 Count	4.07 VDC
1789946516	303 Count	841 Count	4.08 VDC
1789945613	302 Count	837 Count	4.08 VDC
1789944709	301 Count	834 Count	4.08 VDC
1789943806	300 Count	830 Count	4.08 VDC
1789942902	299 Count	826 Count	4.08 VDC
1789941999	298 Count	822 Count	4.08 VDC
1789941095	297 Count	819 Count	4.08 VDC
1789940192	296 Count	815 Count	4.08 VDC
1789939288	295 Count	813 Count	4.08 VDC
1789938386	294 Count	810 Count	4.08 VDC
1789937481	293 Count	807 Count	4.08 VDC
1789936578	292 Count	804 Count	4.09 VDC
1789934770	290 Count	801 Count	4.09 VDC
1789933867	289 Count	798 Count	4.07 VDC
1789933046	284 Count	796 Count	4.1 VDC
1789932142	283 Count	793 Count	4.1 VDC
1789931238	282 Count	789 Count	4.1 VDC
1789930335	281 Count	785 Count	4.1 VDC
1789929431	280 Count	782 Count	4.1 VDC
1789928528	279 Count	779 Count	4.1 VDC

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)