BA5AG-13 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BA5AG-13. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	BattV*	LoadA*	NetA*
1788618886	13.1 V	1.3 A	-1.4 A
1788618579	13.1 V	1.9 A	-2 A
1788618273	13.1 V	1.3 A	-1.4 A
1788617952	13.1 V	1.3 A	-1.3 A
1788617650	13.1 V	2 A	-2 A
1788617349	13.1 V	1.3 A	-1.3 A
1788617048	13.1 V	2 A	-2 A
1788616707	13.1 V	1.3 A	-1.4 A
1788616386	13.1 V	2 A	-2 A
1788616084	13.1 V	1.9 A	-2 A
1788615778	13.1 V	2 A	-2.1 A
1788615477	13.1 V	1.2 A	-1.3 A
1788615171	13.1 V	2 A	-2.1 A
1788614865	13.1 V	1.4 A	-1.4 A
1788614562	13.1 V	1.9 A	-2 A
1788614261	13.1 V	1.2 A	-1.3 A
1788613959	13.1 V	2 A	-2 A
1788613657	13.1 V	1.3 A	-1.3 A
1788613351	13.1 V	2 A	-2.1 A
1788613050	13.1 V	1.2 A	-1.3 A
1788612748	13.1 V	2 A	-2 A
1788612442	13.1 V	1.3 A	-1.3 A
1788612141	13.1 V	1.9 A	-2 A
1788611840	13.1 V	1.2 A	-1.3 A
1788611519	13.1 V	1.9 A	-2 A

*Used Equation Coefficients:

BattV: 0, 0.1, 0

ChgA: 0, 0.1, 0

LoadA: 0, 0.1, 0

NetA: 0, 0.1, -10

Mains: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)