This is the latest recevied telemetry packets stored in our database for station/object IU1VDW-3. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
Time
IAQ*
CO2*
VOC*
GAS*
n/a*
1788661757
56.87 idx
496.47 ppm
0.49 mg/m3
174529 ohm
0 -
1788659357
49.03 idx
496.47 ppm
0.49 mg/m3
174529 ohm
0 -
1788656958
49.03 idx
496.47 ppm
0.49 mg/m3
168646 ohm
0 -
1788654558
50.99 idx
496.47 ppm
0.49 mg/m3
166685 ohm
0 -
1788652158
88.25 idx
592.94 ppm
0.69 mg/m3
162763 ohm
0 -
1788649758
50.99 idx
496.47 ppm
0.49 mg/m3
164724 ohm
0 -
1788647358
49.03 idx
496.47 ppm
0.49 mg/m3
152958 ohm
0 -
1788644958
49.03 idx
496.47 ppm
0.49 mg/m3
147075 ohm
0 -
1788642558
49.03 idx
496.47 ppm
0.49 mg/m3
141192 ohm
0 -
1788640158
49.03 idx
496.47 ppm
0.49 mg/m3
133348 ohm
0 -
1788637758
49.03 idx
496.47 ppm
0.49 mg/m3
119621 ohm
0 -
1788635358
49.03 idx
496.47 ppm
0.49 mg/m3
109816 ohm
0 -
1788632958
49.03 idx
496.47 ppm
0.49 mg/m3
96089 ohm
0 -
1788630558
37.26 idx
400 ppm
0.39 mg/m3
78440 ohm
0 -
1788628158
49.03 idx
496.47 ppm
0.49 mg/m3
31376 ohm
0 -
*Used Equation Coefficients:
IAQ: 0, 1.961, 0
CO2: 0, 96.47, 400
VOC: 0, 0.098, 0
GAS: 0, 1961, 0
n/a: 0, 1, 0
The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0). The sent equation coefficients is used in the equation: a * value2 + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)