DL9DMN-6 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DL9DMN-6. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	Temp*	Humi*	Baro*
1784676900	19.2 deg C	55.5 %	0 hPa
1784676000	19.3 deg C	55.6 %	1024.9 hPa
1784675100	19.3 deg C	55.7 %	1025.1 hPa
1784674200	19.4 deg C	55.7 %	1025.4 hPa
1784673300	19.5 deg C	55.7 %	1025.2 hPa
1784672400	19.6 deg C	55.7 %	1025.1 hPa
1784671500	19.6 deg C	55.8 %	0 hPa
1784670600	19.7 deg C	56 %	1023 hPa
1784670270	19.7 deg C	56 %	1022.4 hPa
1784669370	19.7 deg C	56 %	1023.9 hPa
1784668470	19.8 deg C	56.1 %	1025.6 hPa
1784667570	19.9 deg C	56.1 %	1025 hPa
1784666670	19.9 deg C	56.1 %	1026.6 hPa
1784665770	20 deg C	56.2 %	1029.5 hPa
1784664872	20.1 deg C	56.3 %	1028.8 hPa
1784663970	20.1 deg C	56.3 %	1032.4 hPa
1784663070	20.2 deg C	56 %	1029.4 hPa
1784662170	20.2 deg C	55.5 %	1026.9 hPa
1784661270	20.3 deg C	55.6 %	1023.1 hPa
1784660371	20.3 deg C	55.5 %	1022.1 hPa
1784659474	20.3 deg C	55.5 %	1024.7 hPa
1784658570	20.3 deg C	55.6 %	1024.7 hPa
1784658242	20.3 deg C	55.6 %	1025.9 hPa
1784657342	20.4 deg C	55.8 %	1025.1 hPa
1784656437	20.3 deg C	54.4 %	1022.5 hPa

*Used Equation Coefficients:

Temp: 0, 0.1, 0

Humi: 0, 0.1, 0

Baro: 0, 0.1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)