VK6KCH-7 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VK6KCH-7. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Latency*	PktLoss*	RackTemp*
1787579732	68 ms	0 percent	11.5 degC
1787579431	68 ms	0 percent	11.78 degC
1787579130	68 ms	0 percent	11.78 degC
1787578830	68 ms	0 percent	11.78 degC
1787578530	68 ms	0 percent	11.78 degC
1787578229	68 ms	0 percent	12.05 degC
1787577930	68 ms	0 percent	12.05 degC
1787577331	68 ms	0 percent	12.05 degC
1787577030	72 ms	0 percent	12.05 degC
1787576731	68 ms	0 percent	12.05 degC
1787576430	72 ms	0 percent	12.05 degC
1787576130	68 ms	0 percent	12.33 degC
1787575830	72 ms	0 percent	12.33 degC
1787575529	68 ms	0 percent	12.33 degC
1787574932	72 ms	10 percent	12.6 degC
1787574330	76 ms	0 percent	12.6 degC
1787574031	68 ms	0 percent	12.88 degC
1787573730	68 ms	0 percent	12.88 degC
1787573429	68 ms	0 percent	12.88 degC
1787572830	72 ms	0 percent	12.88 degC
1787572531	68 ms	0 percent	12.88 degC
1787571932	68 ms	0 percent	13.15 degC
1787571631	84 ms	0 percent	13.15 degC
1787571330	68 ms	0 percent	13.15 degC
1787571031	68 ms	0 percent	13.43 degC

*Used Equation Coefficients:

Latency: 0, 4, 0

PktLoss: 0, 1, 0

RackTemp: 0, 0.275, -5

Res4: 0, 1, 0

Res5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)