EA5JZU-9 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object EA5JZU-9. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Celsius*	Rel_Hum*	Atm_Press*
1787401284	31.9 C	64.9 %	1013.13 hPa
1787399681	30.2 C	38.86 %	1014.63 hPa
1787397057	27.6 C	41.28 %	1014 hPa
1787396636	28.1 C	40.65 %	1013.5 hPa
1787396435	28.2 C	40.64 %	1013.13 hPa
1787396106	28.4 C	40.28 %	1012.88 hPa
1787395494	28.9 C	40.66 %	1022.38 hPa
1787395324	29.5 C	40.7 %	1013.75 hPa
1787395012	30 C	40.06 %	1012.75 hPa
1787394802	30.4 C	39.85 %	1015.5 hPa
1787394623	31.2 C	39.78 %	1016.38 hPa
1787394395	33.1 C	39.85 %	1015.5 hPa
1787393255	33.7 C	57.29 %	1004.63 hPa
1787392189	33.4 C	57.97 %	1004.25 hPa
1787391960	33.6 C	59.77 %	1004.13 hPa
1787391441	34.5 C	60.25 %	1011.63 hPa
1787391400	34.7 C	61.77 %	1013 hPa
1787390889	35.4 C	53.15 %	1016.5 hPa
1787388614	31.7 C	52.12 %	1016.75 hPa
1787388304	32.2 C	51.85 %	1015.13 hPa
1787388089	32.9 C	52.78 %	1014 hPa
1787387907	33.5 C	52.69 %	1014.38 hPa
1787387635	34.8 C	54.4 %	1015.88 hPa
1787387380	35.3 C	63.15 %	1015.63 hPa
1787376015	33.1 C	63.24 %	1013 hPa

*Used Equation Coefficients:

Celsius: 0, 0.1, -50

Rel_Hum: 0, 0.01, 0

Atm_Press: 0, 0.125, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)