ZL4AA-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object ZL4AA-11. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Batt Volts*	PV Volts*	Value5*
1773056403	12.6 V	0 V	11
1773055803	12.6 V	0 V	11.1
1773055203	12.6 V	0 V	11.3
1773054603	12.6 V	0 V	11.5
1773054003	12.6 V	0 V	11.6
1773053403	12.7 V	0 V	11.8
1773052803	12.7 V	0 V	12
1773052203	12.7 V	0 V	12.2
1773051603	12.7 V	0 V	12.3
1773051003	12.7 V	0 V	12.5
1773050403	12.7 V	0 V	12.7
1773049803	12.7 V	0 V	12.9
1773049203	12.7 V	0 V	13.1
1773048604	12.7 V	0 V	13.2
1773048004	12.7 V	0 V	13.3
1773047402	12.7 V	0 V	13.5
1773046803	12.7 V	0 V	13.6
1773046203	12.7 V	0 V	13.8
1773045605	12.7 V	0 V	14
1773045003	12.7 V	0 V	14.2
1773044403	12.8 V	0 V	14.5
1773043803	12.8 V	0 V	14.7
1773043203	12.8 V	0.1 V	15
1773042603	12.8 V	0.8 V	15.2
1773042004	12.8 V	4.7 V	15.4

*Used Equation Coefficients:

Batt Volts: 0, 0.1, 0

Batt Amps: 0, 0.1, 0

PV Volts: 0, 0.1, 0

PV Watts: 0, 1, 0

Value5: 0, 0.1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)