OZ0LLH Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OZ0LLH. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	Vin*	Rx1h*	Dg1h*	Eff1h*
1761554986	13.95 Volt	100 Pkt	40 Pkt	52 Pcnt
1761554983	13.95 Volt	100 Pkt	40 Pkt	52 Pcnt
1761554384	14.18 Volt	100 Pkt	40 Pkt	55 Pcnt
1761553784	14.18 Volt	100 Pkt	40 Pkt	51 Pcnt
1761553184	14.18 Volt	100 Pkt	40 Pkt	48 Pcnt
1761552584	14.1 Volt	90 Pkt	40 Pkt	48 Pcnt
1761551984	14.1 Volt	90 Pkt	40 Pkt	49 Pcnt
1761551384	13.8 Volt	100 Pkt	40 Pkt	50 Pcnt
1761551383	13.8 Volt	100 Pkt	40 Pkt	50 Pcnt
1761550784	14.03 Volt	100 Pkt	40 Pkt	49 Pcnt
1761550184	14.03 Volt	100 Pkt	40 Pkt	53 Pcnt
1761549584	13.95 Volt	100 Pkt	40 Pkt	53 Pcnt
1761548984	13.95 Volt	120 Pkt	30 Pkt	52 Pcnt
1761548385	13.95 Volt	130 Pkt	40 Pkt	47 Pcnt
1761547786	13.8 Volt	150 Pkt	50 Pkt	45 Pcnt
1761547783	13.8 Volt	150 Pkt	50 Pkt	45 Pcnt
1761547184	13.88 Volt	160 Pkt	60 Pkt	45 Pcnt
1761546584	13.88 Volt	180 Pkt	80 Pkt	46 Pcnt
1761545984	13.8 Volt	190 Pkt	90 Pkt	48 Pcnt
1761545384	13.8 Volt	200 Pkt	90 Pkt	48 Pcnt
1761544784	13.8 Volt	190 Pkt	90 Pkt	48 Pcnt
1761544186	13.73 Volt	160 Pkt	80 Pkt	50 Pcnt
1761544184	13.73 Volt	160 Pkt	80 Pkt	50 Pcnt
1761543584	13.8 Volt	170 Pkt	70 Pkt	53 Pcnt
1761542984	13.73 Volt	150 Pkt	60 Pkt	52 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)