VU3BOP-13 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VU3BOP-13. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	RSSI*	FreeHeap*	Uptime*	OKSend*
1787654446	-46 dBm	33 KB	110 min	12 cnt
1787653845	-43 dBm	33 KB	100 min	11 cnt
1787653245	-37 dBm	34 KB	90 min	10 cnt
1787652645	-35 dBm	33 KB	80 min	9 cnt
1787652045	-37 dBm	34 KB	70 min	8 cnt
1787651444	-44 dBm	34 KB	60 min	7 cnt
1787650845	-54 dBm	34 KB	50 min	6 cnt
1787650246	-55 dBm	33 KB	40 min	5 cnt
1787649645	-47 dBm	34 KB	30 min	4 cnt
1787649045	-50 dBm	34 KB	20 min	3 cnt
1787648446	-44 dBm	33 KB	10 min	2 cnt
1787647845	-41 dBm	35 KB	0 min	1 cnt
1787647457	-56 dBm	36 KB	10 min	2 cnt
1787646681	-39 dBm	35 KB	0 min	1 cnt
1787646591	-33 dBm	35 KB	80 min	9 cnt
1787645991	-38 dBm	35 KB	70 min	8 cnt
1787645392	-39 dBm	35 KB	60 min	7 cnt
1787644791	-40 dBm	35 KB	50 min	6 cnt
1787644191	-42 dBm	35 KB	40 min	5 cnt
1787643590	-38 dBm	35 KB	30 min	4 cnt
1787642991	-36 dBm	36 KB	20 min	3 cnt
1787642391	-39 dBm	36 KB	10 min	2 cnt
1787641791	-41 dBm	36 KB	0 min	1 cnt

*Used Equation Coefficients:

RSSI: 0, 1, 0

FreeHeap: 0, 1, 0

Uptime: 0, 1, 0

OKSend: 0, 1, 0

FailSend: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)