ABAJO Telemetry

This is the latest recevied telemetry packets stored in our database for station/object ABAJO. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Dg1h*	Eff1h*
1784689401	13.67 Volt	520 Pkt	30 Pkt	68 Pcnt
1784689102	13.67 Volt	530 Pkt	30 Pkt	68 Pcnt
1784689101	13.67 Volt	530 Pkt	30 Pkt	68 Pcnt
1784688801	13.67 Volt	550 Pkt	30 Pkt	68 Pcnt
1784688526	13.67 Volt	560 Pkt	20 Pkt	68 Pcnt
1784688502	13.67 Volt	560 Pkt	20 Pkt	68 Pcnt
1784688201	13.67 Volt	580 Pkt	20 Pkt	69 Pcnt
1784687902	13.67 Volt	600 Pkt	20 Pkt	69 Pcnt
1784687901	13.67 Volt	600 Pkt	20 Pkt	69 Pcnt
1784687601	13.59 Volt	610 Pkt	20 Pkt	68 Pcnt
1784687302	13.67 Volt	590 Pkt	20 Pkt	66 Pcnt
1784687302	13.67 Volt	590 Pkt	20 Pkt	66 Pcnt
1784687001	13.67 Volt	580 Pkt	10 Pkt	64 Pcnt
1784686702	13.67 Volt	590 Pkt	10 Pkt	63 Pcnt
1784686702	13.67 Volt	590 Pkt	10 Pkt	63 Pcnt
1784686402	13.67 Volt	600 Pkt	10 Pkt	62 Pcnt
1784686102	13.67 Volt	600 Pkt	0 Pkt	62 Pcnt
1784686102	13.67 Volt	600 Pkt	0 Pkt	62 Pcnt
1784685802	13.67 Volt	610 Pkt	0 Pkt	62 Pcnt
1784685506	13.67 Volt	620 Pkt	0 Pkt	63 Pcnt
1784685502	13.67 Volt	620 Pkt	0 Pkt	63 Pcnt
1784685202	13.67 Volt	620 Pkt	0 Pkt	64 Pcnt
1784684902	13.59 Volt	600 Pkt	0 Pkt	63 Pcnt
1784684902	13.59 Volt	600 Pkt	0 Pkt	63 Pcnt
1784684602	13.59 Volt	590 Pkt	0 Pkt	63 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.079, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)