DR0T-99 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DR0T-99. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	U-L1*	U-L2*	U-L3*	P-W*	P-VA*
1788402000	239 V	237 V	239 V	22 W	64 VA
1788401400	239 V	237 V	238 V	23 W	63 VA
1788400800	238 V	237 V	238 V	22 W	62 VA
1788400200	238 V	237 V	238 V	22 W	64 VA
1788399600	238 V	236 V	238 V	23 W	65 VA
1788399000	238 V	236 V	238 V	22 W	66 VA
1788398400	238 V	236 V	238 V	22 W	65 VA
1788397800	238 V	237 V	238 V	49 W	74 VA
1788397200	239 V	237 V	239 V	50 W	75 VA
1788396600	238 V	237 V	238 V	51 W	76 VA
1788396000	238 V	237 V	238 V	52 W	78 VA
1788395400	238 V	237 V	238 V	22 W	66 VA
1788394800	238 V	237 V	238 V	23 W	67 VA
1788394200	239 V	237 V	239 V	22 W	66 VA
1788393600	239 V	237 V	239 V	22 W	67 VA
1788393000	239 V	237 V	239 V	22 W	67 VA
1788392400	238 V	237 V	238 V	22 W	65 VA
1788391800	238 V	236 V	238 V	22 W	65 VA
1788391200	238 V	237 V	238 V	22 W	66 VA
1788390600	238 V	236 V	238 V	23 W	67 VA
1788390000	238 V	237 V	238 V	48 W	73 VA
1788389400	238 V	237 V	238 V	50 W	74 VA
1788388800	238 V	237 V	238 V	50 W	75 VA
1788388200	238 V	237 V	238 V	53 W	79 VA
1788387600	238 V	237 V	238 V	22 W	67 VA

*Used Equation Coefficients:

U-L1: 0, 1, 0

U-L2: 0, 1, 0

U-L3: 0, 1, 0

P-W: 0, 1, 0

P-VA: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)