PD1AQM-15 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object PD1AQM-15. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	TX*	RX*	Digi*	V_Bat*	V_Ext*
1788572931	0 Count	0 Count	0 Count	0 VDC	0 VDC
1788571131	0 Count	0 Count	0 Count	0 VDC	0 VDC
1788569331	0 Count	0 Count	0 Count	0 VDC	0 VDC
1788567531	0 Count	0 Count	0 Count	0 VDC	0 VDC
1788565731	0 Count	0 Count	0 Count	0 VDC	0 VDC
1788563931	0 Count	0 Count	0 Count	0 VDC	0 VDC
1788562131	0 Count	0 Count	0 Count	0 VDC	0 VDC
1788560331	0 Count	0 Count	0 Count	0 VDC	0 VDC
1788558530	0 Count	0 Count	0 Count	0 VDC	0 VDC
1788556730	0 Count	0 Count	0 Count	0 VDC	0 VDC
1788554930	0 Count	0 Count	0 Count	0 VDC	0 VDC
1788553130	0 Count	0 Count	0 Count	0 VDC	0 VDC
1788551330	0 Count	0 Count	0 Count	0 VDC	0 VDC
1788549544	0 Count	0 Count	0 Count	0 VDC	0 VDC
1788547727	0 Count	0 Count	0 Count	0 VDC	0 VDC
1788545927	0 Count	0 Count	0 Count	0 VDC	0 VDC
1788544127	0 Count	0 Count	0 Count	0 VDC	0 VDC
1788542327	0 Count	0 Count	0 Count	0 VDC	0 VDC
1788540527	0 Count	0 Count	0 Count	0 VDC	0 VDC
1788538727	0 Count	0 Count	0 Count	0 VDC	0 VDC
1788536927	0 Count	0 Count	0 Count	0 VDC	0 VDC
1788535127	0 Count	0 Count	0 Count	0 VDC	0 VDC
1788533327	0 Count	0 Count	0 Count	0 VDC	0 VDC
1788531527	0 Count	0 Count	0 Count	0 VDC	0 VDC
1788529726	0 Count	0 Count	0 Count	0 VDC	0 VDC

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)