YD1OCG-14 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YD1OCG-14. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	CPU_Temp*	CPU_Load*	CPU_Freq*	RAM_Free*	Drive_Temp*
1789939790	40 C	9 %	1342 MHz	16 %	35 C
1789939502	40 C	11 %	1756 MHz	16 %	35 C
1789939230	40 C	34 %	1724 MHz	17 %	35 C
1789938965	40 C	9 %	1750 MHz	16 %	35 C
1789938675	40 C	5 %	1333 MHz	17 %	35 C
1789938410	40 C	9 %	1536 MHz	17 %	35 C
1789938145	40 C	9 %	1413 MHz	17 %	35 C
1789937890	40 C	9 %	1833 MHz	17 %	35 C
1789937640	40 C	32 %	2083 MHz	18 %	35 C
1789937390	40 C	6 %	2000 MHz	18 %	35 C
1789937145	40 C	8 %	2083 MHz	18 %	35 C
1789936870	40 C	7 %	1575 MHz	18 %	35 C
1789936589	40 C	8 %	2250 MHz	18 %	35 C
1789936325	40 C	31 %	2416 MHz	18 %	35 C
1789936065	40 C	8 %	2167 MHz	19 %	35 C
1789935795	40 C	7 %	1333 MHz	19 %	35 C
1789935515	40 C	9 %	1500 MHz	19 %	35 C
1789935270	40 C	10 %	2167 MHz	19 %	35 C
1789935020	40 C	33 %	2416 MHz	19 %	35 C
1789934775	40 C	7 %	2000 MHz	20 %	35 C
1789934510	40 C	9 %	2416 MHz	20 %	35 C
1789934225	40 C	7 %	1688 MHz	20 %	35 C
1789933980	40 C	8 %	1572 MHz	20 %	35 C
1789933720	40 C	8 %	2000 MHz	20 %	35 C
1789933460	40 C	9 %	1789 MHz	20 %	35 C

*Used Equation Coefficients:

CPU_Temp: 0, 1, 0

CPU_Load: 0, 1, 0

CPU_Freq: 0, 1, 0

RAM_Free: 0, 1, 0

Drive_Temp: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)