This is the latest recevied telemetry packets stored in our database for station/object G1SOM-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
Time
Sate*
Temp*
Volt*
Alt*
A5*
1787578945
12
80.6 F
3.44 V
20 M
0
1787572295
12
81.6 F
3.51 V
30 M
0
1787570423
12
81.8 F
3.68 V
30 M
0
1787569767
12
80.7 F
3.68 V
10 M
0
1787567194
12
72.6 F
3.48 V
30 M
0
1787560548
12
69.9 F
3.52 V
20 M
0
1787547387
12
65.6 F
3.63 V
30 M
0
1787540544
12
68 F
3.69 V
30 M
0
1787533896
12
71.2 F
3.75 V
40 M
0
1787520599
12
78.2 F
3.89 V
20 M
0
1787513953
12
83.4 F
3.97 V
20 M
0
1787507315
12
88.7 F
4.03 V
20 M
0
1787502647
12
93.2 F
4.12 V
40 M
0
1787502360
12
93.7 F
4.12 V
50 M
0
1786997018
12
79.5 F
3.49 V
20 M
0
1786983723
12
87.6 F
3.63 V
10 M
0
1786977077
12
86.9 F
3.7 V
20 M
0
1786974311
12
89.2 F
3.85 V
20 M
0
1786972524
12
90.8 F
3.83 V
10 M
0
1786972369
12
88.1 F
3.84 V
40 M
0
1786971119
12
87.8 F
3.8 V
90 M
0
*Used Equation Coefficients:
Sate: 0, 1, 0
Temp: 0, 0.1, -50
Volt: 0, 0.01, 0
Alt: 0, 10, 0
A5: 0, 1, 0
The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0). The sent equation coefficients is used in the equation: a * value2 + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)