W1MDM-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object W1MDM-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1784773677	12.23 Volt	80 Pkt	90 Pcnt
1784773377	12.23 Volt	90 Pkt	92 Pcnt
1784773077	12.23 Volt	90 Pkt	93 Pcnt
1784772777	12.23 Volt	90 Pkt	94 Pcnt
1784772477	12.23 Volt	100 Pkt	93 Pcnt
1784772177	12.23 Volt	100 Pkt	94 Pcnt
1784771877	12.23 Volt	100 Pkt	92 Pcnt
1784771577	12.23 Volt	100 Pkt	90 Pcnt
1784771277	12.23 Volt	100 Pkt	89 Pcnt
1784770977	12.23 Volt	100 Pkt	91 Pcnt
1784770677	12.23 Volt	100 Pkt	91 Pcnt
1784770377	12.23 Volt	100 Pkt	91 Pcnt
1784770077	12.23 Volt	90 Pkt	90 Pcnt
1784769777	12.23 Volt	90 Pkt	90 Pcnt
1784769489	12.23 Volt	90 Pkt	90 Pcnt
1784769177	12.23 Volt	90 Pkt	90 Pcnt
1784768877	12.23 Volt	100 Pkt	92 Pcnt
1784768577	12.23 Volt	100 Pkt	93 Pcnt
1784768277	12.23 Volt	100 Pkt	95 Pcnt
1784767977	12.23 Volt	100 Pkt	100 Pcnt
1784767677	12.23 Volt	100 Pkt	99 Pcnt
1784767377	12.23 Volt	100 Pkt	99 Pcnt
1784767077	12.23 Volt	110 Pkt	97 Pcnt
1784766777	12.23 Volt	110 Pkt	96 Pcnt
1784766477	12.23 Volt	100 Pkt	96 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)