VK4RAI-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VK4RAI-3. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Dg1h*	Eff1h*
1761546704	13.9 Volt	280 Pkt	100 Pkt	86 Pcnt
1761546404	13.9 Volt	290 Pkt	100 Pkt	86 Pcnt
1761546104	13.9 Volt	290 Pkt	100 Pkt	86 Pcnt
1761545804	13.9 Volt	290 Pkt	90 Pkt	87 Pcnt
1761545504	13.9 Volt	300 Pkt	100 Pkt	89 Pcnt
1761545204	13.9 Volt	310 Pkt	100 Pkt	88 Pcnt
1761544904	13.9 Volt	300 Pkt	100 Pkt	88 Pcnt
1761544604	13.9 Volt	300 Pkt	100 Pkt	87 Pcnt
1761544304	13.98 Volt	300 Pkt	100 Pkt	87 Pcnt
1761544004	13.9 Volt	290 Pkt	90 Pkt	87 Pcnt
1761543704	13.9 Volt	290 Pkt	90 Pkt	88 Pcnt
1761543404	13.9 Volt	290 Pkt	100 Pkt	88 Pcnt
1761543104	13.9 Volt	300 Pkt	100 Pkt	89 Pcnt
1761542804	13.9 Volt	300 Pkt	100 Pkt	90 Pcnt
1761542504	13.9 Volt	290 Pkt	100 Pkt	88 Pcnt
1761542204	13.9 Volt	270 Pkt	90 Pkt	87 Pcnt
1761541904	13.9 Volt	270 Pkt	90 Pkt	87 Pcnt
1761541604	13.9 Volt	260 Pkt	90 Pkt	87 Pcnt
1761541304	13.9 Volt	240 Pkt	90 Pkt	86 Pcnt
1761541004	13.9 Volt	240 Pkt	90 Pkt	87 Pcnt
1761540704	13.9 Volt	230 Pkt	80 Pkt	88 Pcnt
1761540404	13.9 Volt	230 Pkt	80 Pkt	87 Pcnt
1761540104	13.98 Volt	210 Pkt	80 Pkt	86 Pcnt
1761539804	13.9 Volt	200 Pkt	70 Pkt	85 Pcnt
1761539504	13.9 Volt	200 Pkt	70 Pkt	84 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.079, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)