NO3B-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object NO3B-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1780575555	14.1 Volt	0 Pkt	6 Pcnt
1780574354	14.1 Volt	0 Pkt	0 Pcnt
1780573155	14.1 Volt	0 Pkt	0 Pcnt
1780571954	14.1 Volt	0 Pkt	100 Pcnt
1780570154	14.1 Volt	0 Pkt	0 Pcnt
1780568354	14.1 Volt	0 Pkt	0 Pcnt
1780567755	14.1 Volt	0 Pkt	0 Pcnt
1780567154	14.1 Volt	0 Pkt	0 Pcnt
1780562356	14.1 Volt	0 Pkt	0 Pcnt
1780561755	14.1 Volt	0 Pkt	100 Pcnt
1780559955	14.1 Volt	0 Pkt	100 Pcnt
1780557555	14.1 Volt	0 Pkt	100 Pcnt
1780556357	14.1 Volt	0 Pkt	100 Pcnt
1780555761	14.1 Volt	0 Pkt	100 Pcnt
1780554555	14.1 Volt	0 Pkt	100 Pcnt
1780553955	14.1 Volt	0 Pkt	100 Pcnt
1780550955	14.1 Volt	0 Pkt	100 Pcnt
1780548556	14.1 Volt	0 Pkt	100 Pcnt
1780541956	14.1 Volt	0 Pkt	100 Pcnt
1780490360	14.1 Volt	30 Pkt	19 Pcnt
1780489758	14.1 Volt	40 Pkt	20 Pcnt
1780489158	14.1 Volt	30 Pkt	20 Pcnt
1780487358	14.1 Volt	0 Pkt	3 Pcnt
1780486158	14.1 Volt	0 Pkt	1 Pcnt
1780485559	14.1 Volt	0 Pkt	0 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)