DH9ZIG-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DH9ZIG-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp*	Humi*	Baro*
1784671781	17.1 deg C	61 %	1023.2 hPa
1784670881	17.5 deg C	60 %	1023.1 hPa
1784669981	17.8 deg C	59 %	1023 hPa
1784669081	17.9 deg C	58.4 %	1022.9 hPa
1784668181	18 deg C	58.7 %	1022.9 hPa
1784667281	18.2 deg C	57.7 %	1022.8 hPa
1784666380	18.5 deg C	56.8 %	1022.7 hPa
1784665480	18.6 deg C	56.6 %	1022.6 hPa
1784664580	18.7 deg C	56.2 %	1022.5 hPa
1784663680	18.9 deg C	55.1 %	1022.5 hPa
1784662780	19.1 deg C	53.4 %	1022.4 hPa
1784661880	19.4 deg C	49.6 %	1022 hPa
1784660980	19.5 deg C	48.8 %	1021.8 hPa
1784660080	19.6 deg C	49.1 %	1021.6 hPa
1784659180	19.8 deg C	50.4 %	1021.5 hPa
1784658280	20 deg C	49.7 %	1021.4 hPa
1784657380	20.5 deg C	48.3 %	1021.1 hPa
1784656479	20.9 deg C	47.7 %	1021 hPa
1784655579	21.2 deg C	46.2 %	1020.7 hPa
1784654679	21.4 deg C	45.4 %	1020.7 hPa
1784653779	21.6 deg C	44.7 %	1020.4 hPa
1784652879	22.1 deg C	44.9 %	1020.2 hPa
1784651979	21.9 deg C	43.3 %	1020.1 hPa
1784651079	22.1 deg C	43.5 %	1020.1 hPa
1784650179	22.3 deg C	43.9 %	1019.9 hPa

*Used Equation Coefficients:

Temp: 0, 0.1, 0

Humi: 0, 0.1, 0

Baro: 0, 0.1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)