SP2KMH Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SP2KMH. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1776703379	12.6 Volt	20 Pkt	26 Pcnt
1776701997	12.6 Volt	20 Pkt	25 Pcnt
1776700616	12.6 Volt	10 Pkt	17 Pcnt
1776699235	12.6 Volt	10 Pkt	22 Pcnt
1776697854	12.6 Volt	30 Pkt	52 Pcnt
1776696472	12.6 Volt	60 Pkt	70 Pcnt
1776693710	12.6 Volt	70 Pkt	98 Pcnt
1776692328	12.6 Volt	30 Pkt	97 Pcnt
1776690947	12.6 Volt	0 Pkt	0 Pcnt
1776689566	12.6 Volt	0 Pkt	0 Pcnt
1776663321	12.6 Volt	0 Pkt	0 Pcnt
1776660558	12.68 Volt	0 Pkt	0 Pcnt
1776656414	12.68 Volt	0 Pkt	0 Pcnt
1776650889	12.68 Volt	0 Pkt	100 Pcnt
1776648126	12.68 Volt	0 Pkt	100 Pcnt
1776643983	12.68 Volt	0 Pkt	0 Pcnt
1776641220	12.68 Volt	0 Pkt	0 Pcnt
1776639839	12.6 Volt	0 Pkt	0 Pcnt
1776638457	12.6 Volt	0 Pkt	0 Pcnt
1776637076	12.6 Volt	0 Pkt	0 Pcnt
1776634313	12.68 Volt	0 Pkt	7 Pcnt
1776632932	12.68 Volt	10 Pkt	13 Pcnt
1776631551	12.6 Volt	20 Pkt	22 Pcnt
1776630169	12.6 Volt	20 Pkt	20 Pcnt
1776627407	12.6 Volt	0 Pkt	2 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)