XE1EE-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object XE1EE-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Dg1h*	Temp*
1788594687	14.77 Volt	20 Pkt	10 Pkt	175 C
1788594686	14.77 Volt	20 Pkt	10 Pkt	175 C
1788589287	14.77 Volt	40 Pkt	10 Pkt	176 C
1788589286	14.77 Volt	40 Pkt	10 Pkt	176 C
1788583887	14.7 Volt	0 Pkt	0 Pkt	176 C
1788583886	14.7 Volt	0 Pkt	0 Pkt	176 C
1788578487	14.7 Volt	0 Pkt	0 Pkt	176 C
1788578487	14.7 Volt	0 Pkt	0 Pkt	176 C
1788573088	14.7 Volt	0 Pkt	0 Pkt	176 C
1788573087	14.7 Volt	0 Pkt	0 Pkt	176 C
1788567688	14.7 Volt	40 Pkt	20 Pkt	177 C
1788567687	14.7 Volt	40 Pkt	20 Pkt	177 C
1788562288	14.7 Volt	10 Pkt	10 Pkt	177 C
1788562287	14.7 Volt	10 Pkt	10 Pkt	177 C
1788556888	14.7 Volt	0 Pkt	0 Pkt	177 C
1788556888	14.7 Volt	0 Pkt	0 Pkt	177 C
1788551489	14.7 Volt	60 Pkt	20 Pkt	175 C
1788551488	14.7 Volt	60 Pkt	20 Pkt	175 C
1788546089	14.7 Volt	20 Pkt	10 Pkt	173 C
1788546088	14.7 Volt	20 Pkt	10 Pkt	173 C
1788540689	14.7 Volt	60 Pkt	10 Pkt	172 C
1788540688	14.7 Volt	60 Pkt	10 Pkt	172 C
1788535289	14.77 Volt	40 Pkt	20 Pkt	172 C
1788535289	14.77 Volt	40 Pkt	20 Pkt	172 C
1788529890	14.7 Volt	30 Pkt	10 Pkt	173 C

*Used Equation Coefficients:

Vin: 0, 0.0735, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Temp: 0, 1, 0

DPtot: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)