N2RWE Telemetry

This is the latest recevied telemetry packets stored in our database for station/object N2RWE. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Eff1h*	Temp*
1784784812	14.18 Volt	1 Pcnt	24.5 C
1784784513	14.18 Volt	3 Pcnt	24.5 C
1784784213	14.18 Volt	5 Pcnt	24.5 C
1784783913	14.18 Volt	7 Pcnt	24.5 C
1784783613	14.18 Volt	7 Pcnt	24.5 C
1784783312	14.18 Volt	8 Pcnt	25 C
1784783013	14.18 Volt	9 Pcnt	25 C
1784782713	14.18 Volt	12 Pcnt	25 C
1784782413	14.18 Volt	14 Pcnt	25 C
1784782113	14.18 Volt	13 Pcnt	25 C
1784781813	14.18 Volt	15 Pcnt	25 C
1784781513	14.18 Volt	18 Pcnt	25 C
1784781212	14.18 Volt	20 Pcnt	25 C
1784780913	14.18 Volt	15 Pcnt	25 C
1784780613	14.18 Volt	15 Pcnt	25 C
1784780313	14.18 Volt	15 Pcnt	25 C
1784780013	14.18 Volt	15 Pcnt	25 C
1784779713	14.18 Volt	13 Pcnt	25 C
1784779413	14.18 Volt	12 Pcnt	25 C
1784779113	14.18 Volt	8 Pcnt	25 C
1784778813	14.18 Volt	5 Pcnt	25 C
1784778513	14.18 Volt	5 Pcnt	25 C
1784778213	14.18 Volt	5 Pcnt	25 C
1784777913	14.18 Volt	2 Pcnt	25.5 C
1784777613	14.18 Volt	2 Pcnt	25 C

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)