W8MAI-15 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object W8MAI-15. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	U1*	Temp*	Rx1h*	Dg1h*
1761675337	13.4 Volt	14.5 C	140 Pkt	70 Pkt
1761675336	13.4 Volt	14.5 C	140 Pkt	70 Pkt
1761673537	13.4 Volt	14 C	130 Pkt	60 Pkt
1761673536	13.4 Volt	14 C	130 Pkt	60 Pkt
1761671737	13.4 Volt	13.5 C	140 Pkt	60 Pkt
1761671736	13.4 Volt	13.5 C	140 Pkt	60 Pkt
1761669937	13.4 Volt	13 C	130 Pkt	40 Pkt
1761669936	13.4 Volt	13 C	130 Pkt	40 Pkt
1761668137	13.4 Volt	12.5 C	120 Pkt	40 Pkt
1761668136	13.4 Volt	12.5 C	120 Pkt	40 Pkt
1761666337	13.4 Volt	12 C	140 Pkt	40 Pkt
1761662737	13.4 Volt	11.5 C	190 Pkt	80 Pkt
1761660937	13.4 Volt	12 C	240 Pkt	100 Pkt
1761659137	13.4 Volt	12 C	220 Pkt	80 Pkt
1761659137	13.4 Volt	12 C	220 Pkt	80 Pkt
1761657337	13.4 Volt	12 C	260 Pkt	90 Pkt
1761657337	13.4 Volt	12 C	260 Pkt	90 Pkt
1761655537	13.4 Volt	12 C	310 Pkt	140 Pkt
1761655537	13.4 Volt	12 C	310 Pkt	140 Pkt
1761651939	13.4 Volt	12 C	300 Pkt	120 Pkt
1761651937	13.4 Volt	12 C	300 Pkt	120 Pkt
1761650140	13.4 Volt	12.5 C	200 Pkt	80 Pkt
1761650137	13.4 Volt	12.5 C	200 Pkt	80 Pkt
1761648338	13.4 Volt	12.5 C	190 Pkt	80 Pkt
1761648337	13.4 Volt	12.5 C	190 Pkt	80 Pkt

*Used Equation Coefficients:

U1: 0, 0.1, 0

U2: 0, 0.1, 0

Temp: 0, 0.5, -64

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)