W7BAN Telemetry

This is the latest recevied telemetry packets stored in our database for station/object W7BAN. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1780605286	14.4 Volt	470 Pkt	80 Pcnt
1780601686	14.4 Volt	140 Pkt	31 Pcnt
1780598086	14.4 Volt	60 Pkt	18 Pcnt
1780594486	14.4 Volt	80 Pkt	19 Pcnt
1780590886	14.4 Volt	140 Pkt	31 Pcnt
1780587286	14.4 Volt	280 Pkt	49 Pcnt
1780583686	14.4 Volt	510 Pkt	91 Pcnt
1780580086	14.4 Volt	470 Pkt	85 Pcnt
1780576487	14.4 Volt	450 Pkt	93 Pcnt
1780572887	14.4 Volt	380 Pkt	93 Pcnt
1780569287	14.4 Volt	280 Pkt	73 Pcnt
1780565687	14.4 Volt	160 Pkt	45 Pcnt
1780562087	14.4 Volt	120 Pkt	33 Pcnt
1780558487	14.4 Volt	100 Pkt	29 Pcnt
1780554887	14.4 Volt	70 Pkt	19 Pcnt
1780551287	14.4 Volt	60 Pkt	17 Pcnt
1780547688	14.4 Volt	160 Pkt	37 Pcnt
1780544088	14.4 Volt	20 Pkt	7 Pcnt
1780540488	14.4 Volt	50 Pkt	12 Pcnt
1780536888	14.4 Volt	0 Pkt	1 Pcnt
1780533288	14.4 Volt	10 Pkt	4 Pcnt
1780529688	14.4 Volt	10 Pkt	5 Pcnt
1780526088	14.4 Volt	240 Pkt	50 Pcnt
1780522488	14.4 Volt	440 Pkt	93 Pcnt
1780518889	14.4 Volt	490 Pkt	94 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)