HARRY Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HARRY. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Temp*	Dg1h*	Eff1h*
1780614684	13.43 Volt	41.5 C	90 Pkt	77 Pcnt
1780614084	13.43 Volt	41.5 C	100 Pkt	78 Pcnt
1780613484	13.43 Volt	41.5 C	100 Pkt	78 Pcnt
1780612884	13.43 Volt	41 C	100 Pkt	78 Pcnt
1780612284	13.43 Volt	41.5 C	100 Pkt	78 Pcnt
1780611684	13.43 Volt	41.5 C	90 Pkt	80 Pcnt
1780611084	13.43 Volt	41.5 C	90 Pkt	81 Pcnt
1780610487	13.43 Volt	41.5 C	90 Pkt	82 Pcnt
1780609284	13.43 Volt	41 C	90 Pkt	82 Pcnt
1780608684	13.43 Volt	41 C	90 Pkt	82 Pcnt
1780608084	13.43 Volt	41 C	90 Pkt	82 Pcnt
1780606884	13.43 Volt	41 C	90 Pkt	83 Pcnt
1780606284	13.43 Volt	41 C	90 Pkt	84 Pcnt
1780605684	13.43 Volt	41 C	90 Pkt	82 Pcnt
1780605084	13.43 Volt	41 C	90 Pkt	82 Pcnt
1780604484	13.43 Volt	41 C	90 Pkt	82 Pcnt
1780603884	13.43 Volt	40.5 C	90 Pkt	79 Pcnt
1780603284	13.43 Volt	40.5 C	90 Pkt	81 Pcnt
1780602684	13.43 Volt	41 C	90 Pkt	80 Pcnt
1780602084	13.43 Volt	41 C	90 Pkt	83 Pcnt
1780601484	13.43 Volt	40.5 C	90 Pkt	83 Pcnt
1780600884	13.43 Volt	40.5 C	90 Pkt	83 Pcnt
1780600284	13.43 Volt	40.5 C	90 Pkt	85 Pcnt
1780599685	13.43 Volt	40 C	90 Pkt	83 Pcnt
1780598484	13.43 Volt	40 C	90 Pkt	83 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Temp: 0, 0.5, -59

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)