VAILMT Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VAILMT. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Dg1h*	Eff1h*
1780560043	14.54 Volt	200 Pkt	40 Pkt	67 Pcnt
1780560042	14.54 Volt	200 Pkt	40 Pkt	67 Pcnt
1780559443	14.54 Volt	210 Pkt	40 Pkt	68 Pcnt
1780559442	14.54 Volt	210 Pkt	40 Pkt	68 Pcnt
1780558843	14.54 Volt	190 Pkt	40 Pkt	67 Pcnt
1780558842	14.54 Volt	190 Pkt	40 Pkt	67 Pcnt
1780558243	14.54 Volt	210 Pkt	40 Pkt	71 Pcnt
1780558242	14.54 Volt	210 Pkt	40 Pkt	71 Pcnt
1780557643	14.54 Volt	220 Pkt	30 Pkt	70 Pcnt
1780557642	14.54 Volt	220 Pkt	30 Pkt	70 Pcnt
1780557043	14.54 Volt	220 Pkt	30 Pkt	70 Pcnt
1780557042	14.54 Volt	220 Pkt	30 Pkt	70 Pcnt
1780556443	14.54 Volt	220 Pkt	30 Pkt	71 Pcnt
1780556442	14.54 Volt	220 Pkt	30 Pkt	71 Pcnt
1780555244	14.54 Volt	220 Pkt	30 Pkt	72 Pcnt
1780555243	14.54 Volt	220 Pkt	30 Pkt	72 Pcnt
1780554643	14.54 Volt	220 Pkt	30 Pkt	71 Pcnt
1780554642	14.54 Volt	220 Pkt	30 Pkt	71 Pcnt
1780554043	14.54 Volt	230 Pkt	30 Pkt	72 Pcnt
1780554042	14.54 Volt	230 Pkt	30 Pkt	72 Pcnt
1780553443	14.54 Volt	220 Pkt	30 Pkt	72 Pcnt
1780553443	14.54 Volt	220 Pkt	30 Pkt	72 Pcnt
1780552843	14.54 Volt	220 Pkt	30 Pkt	72 Pcnt
1780552843	14.54 Volt	220 Pkt	30 Pkt	72 Pcnt
1780552243	14.54 Volt	230 Pkt	30 Pkt	74 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.079, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)