KI0AU-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object KI0AU-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Tbatt*	Rx1h*	Dg1h*
1788574809	35.5 C	170 Pkt	20 Pkt
1788573608	35.5 C	130 Pkt	20 Pkt
1788572407	36 C	100 Pkt	20 Pkt
1788571205	36 C	80 Pkt	10 Pkt
1788570008	36.5 C	70 Pkt	10 Pkt
1788567602	36.5 C	80 Pkt	10 Pkt
1788566401	37 C	80 Pkt	20 Pkt
1788565200	37 C	70 Pkt	20 Pkt
1788563999	37 C	60 Pkt	20 Pkt
1788562798	37 C	50 Pkt	10 Pkt
1788561596	37 C	70 Pkt	20 Pkt
1788560395	36.5 C	80 Pkt	30 Pkt
1788559194	36.5 C	90 Pkt	30 Pkt
1788557993	36.5 C	80 Pkt	30 Pkt
1788556792	36 C	80 Pkt	30 Pkt
1788554390	35.5 C	70 Pkt	30 Pkt
1788551987	35 C	50 Pkt	20 Pkt
1788549585	34 C	60 Pkt	20 Pkt
1788548384	34 C	70 Pkt	30 Pkt
1788547183	33.5 C	90 Pkt	40 Pkt
1788545982	33.5 C	90 Pkt	50 Pkt
1788544781	33 C	90 Pkt	40 Pkt
1788543580	32.5 C	80 Pkt	30 Pkt
1788541178	31.5 C	80 Pkt	30 Pkt
1788539976	31.5 C	80 Pkt	20 Pkt

*Used Equation Coefficients:

Tbatt: 0, 0.5, -64

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

InVolt: 0, 0, 0

Vbatt: 0, 0.1377, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)