OE1ACM-27 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OE1ACM-27. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp*	Pres*	Humi*
1788622601	33.5 deg.C	999 mbar	29 Percen
1788622301	33.5 deg.C	999 mbar	29 Percen
1788622001	33.5 deg.C	999 mbar	30 Percen
1788621701	33.5 deg.C	999 mbar	29 Percen
1788621401	33.5 deg.C	999 mbar	29 Percen
1788621101	33.5 deg.C	999 mbar	29 Percen
1788620801	33.5 deg.C	999 mbar	29 Percen
1788620501	33.5 deg.C	999 mbar	29 Percen
1788620201	33.5 deg.C	999 mbar	29 Percen
1788619901	33.5 deg.C	999 mbar	30 Percen
1788619601	33.5 deg.C	999 mbar	29 Percen
1788619301	33.5 deg.C	999 mbar	29 Percen
1788619001	33.5 deg.C	999 mbar	29 Percen
1788618701	33.5 deg.C	999 mbar	30 Percen
1788618401	33.5 deg.C	999 mbar	30 Percen
1788618101	33.5 deg.C	999 mbar	29 Percen
1788617801	33.5 deg.C	999 mbar	29 Percen
1788617501	33.5 deg.C	999 mbar	29 Percen
1788617201	33.5 deg.C	999 mbar	29 Percen
1788616901	33.5 deg.C	1000 mbar	29 Percen
1788616601	33.5 deg.C	1000 mbar	30 Percen
1788616301	33.5 deg.C	1000 mbar	29 Percen
1788616001	33.5 deg.C	1000 mbar	29 Percen
1788615701	33.5 deg.C	1000 mbar	29 Percen
1788615401	33.5 deg.C	1000 mbar	29 Percen

*Used Equation Coefficients:

Temp: 0, 0.5, -40

Pres: 0, 1, 850

Humi: 0, 0.5, 0

xxx: 0, 1, 0

yyy: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)