BM1CKC-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BM1CKC-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	CPUTemp*	RxPkts/20m*	RxPkts/1h*	RxPkts/24h*
1788598556	40.3 C	35 p	123 p	3706 p
1788597356	40.7 C	46 p	146 p	3778 p
1788596157	40.6 C	42 p	168 p	3891 p
1788594957	39.2 C	58 p	190 p	3991 p
1788593756	39.2 C	68 p	211 p	3976 p
1788592556	40.8 C	64 p	207 p	3962 p
1788591356	40.1 C	79 p	219 p	3940 p
1788590168	40.8 C	64 p	193 p	3918 p
1788588957	40 C	76 p	178 p	3995 p
1788587757	39.5 C	53 p	149 p	3965 p
1788586557	38.9 C	49 p	133 p	3952 p
1788585359	39.9 C	47 p	143 p	3944 p
1788584159	39.9 C	37 p	192 p	3936 p
1788582956	39.2 C	59 p	198 p	3938 p
1788581757	39.5 C	96 p	186 p	3920 p
1788580563	40.3 C	43 p	129 p	3866 p
1788579363	40.5 C	47 p	142 p	3864 p
1788578168	39.4 C	39 p	168 p	3860 p
1788576965	39.6 C	56 p	171 p	3858 p
1788575764	40.2 C	73 p	157 p	3844 p
1788574563	39.7 C	42 p	123 p	3811 p
1788573363	39.9 C	42 p	122 p	3814 p
1788572162	39.4 C	39 p	117 p	3811 p
1788570962	38.8 C	41 p	113 p	3816 p
1788569773	38.3 C	37 p	107 p	3817 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/20m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)