OE3XOC-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OE3XOC-11. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp*	Pres*	Humi*
1788597920	18.5 deg.C	965 mbar	72 Percen
1788597620	18.5 deg.C	965 mbar	70 Percen
1788597320	18 deg.C	965 mbar	69 Percen
1788597020	18 deg.C	965 mbar	70 Percen
1788596720	18 deg.C	965 mbar	68 Percen
1788596420	18 deg.C	966 mbar	70 Percen
1788596035	18 deg.C	966 mbar	70 Percen
1788595735	18 deg.C	966 mbar	70 Percen
1788595435	18 deg.C	966 mbar	69 Percen
1788595135	18.5 deg.C	966 mbar	66 Percen
1788594835	19 deg.C	966 mbar	63 Percen
1788594535	19 deg.C	966 mbar	63 Percen
1788594235	19 deg.C	966 mbar	63 Percen
1788593935	19 deg.C	966 mbar	63 Percen
1788593635	18.5 deg.C	966 mbar	65 Percen
1788593335	19 deg.C	966 mbar	63 Percen
1788593035	18.5 deg.C	966 mbar	63 Percen
1788592735	19 deg.C	966 mbar	64 Percen
1788592435	18.5 deg.C	966 mbar	65 Percen
1788592135	18.5 deg.C	966 mbar	65 Percen
1788591835	19 deg.C	966 mbar	64 Percen
1788591535	19 deg.C	966 mbar	64 Percen
1788591235	19.5 deg.C	965 mbar	60 Percen
1788590935	20 deg.C	965 mbar	59 Percen
1788590635	20 deg.C	965 mbar	60 Percen

*Used Equation Coefficients:

Temp: 0, 0.5, -40

Pres: 0, 1, 850

Humi: 0, 0.5, 0

xxx: 0, 1, 0

yyy: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)