ED4YAO-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object ED4YAO-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	VDCin*	Temp*	Eff*
1780544739	13.8 Volt	26 C	100 Pcnt
1780544439	13.8 Volt	26 C	100 Pcnt
1780544139	13.8 Volt	25.5 C	100 Pcnt
1780543839	13.8 Volt	25.5 C	100 Pcnt
1780543539	13.8 Volt	25.5 C	100 Pcnt
1780543239	13.8 Volt	25.5 C	100 Pcnt
1780542939	13.8 Volt	25.5 C	100 Pcnt
1780542639	13.8 Volt	26 C	100 Pcnt
1780542339	13.8 Volt	25.5 C	100 Pcnt
1780542039	13.8 Volt	25.5 C	100 Pcnt
1780541739	13.8 Volt	25.5 C	100 Pcnt
1780541439	13.8 Volt	25.5 C	100 Pcnt
1780541139	13.8 Volt	25.5 C	100 Pcnt
1780540839	13.8 Volt	25.5 C	100 Pcnt
1780540539	13.8 Volt	25.5 C	100 Pcnt
1780540239	13.8 Volt	25.5 C	100 Pcnt
1780539939	13.8 Volt	25.5 C	100 Pcnt
1780539639	13.8 Volt	25.5 C	100 Pcnt
1780539339	13.8 Volt	25.5 C	100 Pcnt
1780539040	13.8 Volt	25.5 C	100 Pcnt
1780538739	13.8 Volt	25.5 C	100 Pcnt
1780538439	13.8 Volt	25.5 C	100 Pcnt
1780538139	13.8 Volt	25.5 C	100 Pcnt
1780537839	13.8 Volt	25.5 C	100 Pcnt
1780537539	13.8 Volt	25.5 C	100 Pcnt

*Used Equation Coefficients:

VDCin: 0, 0.075, 0

Temp: 0, 0.5, -64

Batt: 0, 0.075, 0

Alert: 0, 0.1953, -24.9984

Eff: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)