VA7GFZ-13 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VA7GFZ-13. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Temp*	Eff1h*
1788578664	26.2 Volt	14 C	730 Pcnt
1788573147	27.6 Volt	14.5 C	730 Pcnt
1788567627	27.6 Volt	15 C	730 Pcnt
1788559347	27.6 Volt	13.5 C	730 Pcnt
1788556585	27.6 Volt	13.5 C	730 Pcnt
1788553827	27.6 Volt	12.5 C	730 Pcnt
1788551067	29 Volt	11.5 C	730 Pcnt
1788545547	29.2 Volt	10.5 C	730 Pcnt
1788542787	28 Volt	10 C	730 Pcnt
1788540028	27.2 Volt	10 C	730 Pcnt
1788534507	26 Volt	10 C	730 Pcnt
1788528989	25.2 Volt	10 C	730 Pcnt
1788526228	25.4 Volt	10.5 C	730 Pcnt
1788523466	25.4 Volt	10.5 C	730 Pcnt
1788520709	25.4 Volt	10.5 C	730 Pcnt
1788517948	25.6 Volt	10.5 C	730 Pcnt
1788515186	25.6 Volt	10.5 C	730 Pcnt
1788512427	25.6 Volt	11 C	730 Pcnt
1788509669	25.6 Volt	11 C	730 Pcnt
1788504149	25.8 Volt	11.5 C	730 Pcnt
1788501387	25.8 Volt	11.5 C	730 Pcnt
1788498627	25.8 Volt	12 C	730 Pcnt
1788495870	25.8 Volt	12 C	730 Pcnt
1788490350	26.4 Volt	13 C	730 Pcnt
1788487587	26.8 Volt	13.5 C	730 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.2, 0

Temp: 0, 0.5, -64

Rx1h: 0, 10, 0

Eff1h: 0, 10, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)