VA3APW-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VA3APW-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1765498758	13.88 Volt	550 Pkt	89 Pcnt
1765497275	13.88 Volt	530 Pkt	87 Pcnt
1765495758	13.88 Volt	550 Pkt	88 Pcnt
1765494258	13.88 Volt	580 Pkt	88 Pcnt
1765492758	13.88 Volt	620 Pkt	90 Pcnt
1765491258	13.88 Volt	660 Pkt	90 Pcnt
1765489758	13.88 Volt	650 Pkt	88 Pcnt
1765488258	13.88 Volt	600 Pkt	87 Pcnt
1765486759	13.88 Volt	490 Pkt	88 Pcnt
1765485259	13.88 Volt	480 Pkt	90 Pcnt
1765483759	13.88 Volt	500 Pkt	90 Pcnt
1765482259	13.88 Volt	510 Pkt	90 Pcnt
1765480759	13.88 Volt	500 Pkt	91 Pcnt
1765479259	13.88 Volt	460 Pkt	91 Pcnt
1765477759	13.88 Volt	440 Pkt	89 Pcnt
1765476259	13.88 Volt	430 Pkt	85 Pcnt
1765474759	13.88 Volt	450 Pkt	85 Pcnt
1765473259	13.88 Volt	500 Pkt	88 Pcnt
1765471759	13.88 Volt	450 Pkt	90 Pcnt
1765470260	13.88 Volt	500 Pkt	91 Pcnt
1765467260	13.88 Volt	470 Pkt	89 Pcnt
1765465760	13.88 Volt	520 Pkt	90 Pcnt
1765464260	13.88 Volt	510 Pkt	90 Pcnt
1765462760	13.88 Volt	520 Pkt	90 Pcnt
1765461260	13.88 Volt	490 Pkt	88 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)