KNAPPA Telemetry

This is the latest recevied telemetry packets stored in our database for station/object KNAPPA. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Battery*	Array-East*	Array-West*
1787570132	13.08 Volts	0.03 V	0.1 V
1787569501	13.09 Volts	0.01 V	0.09 V
1787568873	13.08 Volts	0.01 V	0 V
1787568243	13.09 Volts	0.03 V	0.01 V
1787567612	13.09 Volts	0.03 V	0.11 V
1787566982	13.09 Volts	0.01 V	0.07 V
1787566422	13.09 Volts	0.02 V	0 V
1787565722	13.09 Volts	0.03 V	0.08 V
1787565092	13.09 Volts	0.02 V	0 V
1787564462	13.09 Volts	0.03 V	0 V
1787563832	13.1 Volts	0.02 V	0 V
1787563203	13.1 Volts	0.01 V	0 V
1787562572	13.1 Volts	0.03 V	0.11 V
1787561942	13.1 Volts	0.02 V	0.08 V
1787561312	13.1 Volts	0.03 V	0 V
1787560681	13.1 Volts	0.05 V	0.13 V
1787560051	13.11 Volts	0.01 V	0.06 V
1787559422	13.11 Volts	0.07 V	0.04 V
1787558791	13.11 Volts	0.02 V	0.05 V
1787558162	13.11 Volts	0.05 V	0.13 V
1787557532	13.11 Volts	0.05 V	0.17 V
1787557038	13.12 Volts	0.05 V	0.09 V
1787556272	13.12 Volts	0.02 V	0.09 V
1787555642	13.12 Volts	0.03 V	0.01 V
1787555012	13.13 Volts	0.03 V	0.11 V

*Used Equation Coefficients:

Battery: 0, 1, 0

Watts: 0, 1, 0

Array-East: 0, 1, 0

Array-West: 0, 1, 0

Charging: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)