SA6BWX-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SA6BWX-2. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1777040356	12.64 Volt	10 Pkt	84 Pcnt
1777040056	12.64 Volt	10 Pkt	83 Pcnt
1777039756	12.64 Volt	10 Pkt	88 Pcnt
1777039456	12.64 Volt	10 Pkt	88 Pcnt
1777039156	12.64 Volt	10 Pkt	87 Pcnt
1777038856	12.64 Volt	10 Pkt	86 Pcnt
1777038556	12.64 Volt	10 Pkt	86 Pcnt
1777038256	12.64 Volt	10 Pkt	85 Pcnt
1777037956	12.64 Volt	10 Pkt	84 Pcnt
1777037656	12.64 Volt	10 Pkt	83 Pcnt
1777037356	12.64 Volt	0 Pkt	100 Pcnt
1777037056	12.64 Volt	0 Pkt	100 Pcnt
1777036756	12.64 Volt	0 Pkt	100 Pcnt
1777036456	12.64 Volt	0 Pkt	100 Pcnt
1777036156	12.64 Volt	0 Pkt	100 Pcnt
1777035856	12.64 Volt	0 Pkt	100 Pcnt
1777035556	12.64 Volt	10 Pkt	100 Pcnt
1777035256	12.64 Volt	0 Pkt	100 Pcnt
1777034956	12.64 Volt	0 Pkt	100 Pcnt
1777034656	12.64 Volt	0 Pkt	100 Pcnt
1777034356	12.64 Volt	0 Pkt	100 Pcnt
1777034056	12.64 Volt	0 Pkt	100 Pcnt
1777033756	12.64 Volt	0 Pkt	100 Pcnt
1777033456	12.64 Volt	0 Pkt	100 Pcnt
1777033156	12.64 Volt	0 Pkt	100 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.079, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)