WA7DEM-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object WA7DEM-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Value1*	Value2*
1788690099	12.48 Volts	69.21 Deg.F
1788686516	12.51 Volts	70.09 Deg.F
1788684724	12.51 Volts	70.09 Deg.F
1788681140	12.54 Volts	70.97 Deg.F
1788679348	12.54 Volts	71.85 Deg.F
1788675765	12.57 Volts	72.73 Deg.F
1788672181	12.6 Volts	74.49 Deg.F
1788670389	12.6 Volts	75.37 Deg.F
1788666805	12.63 Volts	77.13 Deg.F
1788665023	12.66 Volts	78.01 Deg.F
1788663222	12.66 Volts	78.89 Deg.F
1788661428	12.69 Volts	80.65 Deg.F
1788656047	12.72 Volts	87.69 Deg.F
1788648872	12.75 Volts	88.57 Deg.F
1788647078	12.8 Volts	90.33 Deg.F
1788645284	12.8 Volts	92.09 Deg.F
1788643491	12.98 Volts	92.09 Deg.F
1788641695	13.01 Volts	91.21 Deg.F
1788639901	12.98 Volts	89.45 Deg.F
1788638107	13.01 Volts	88.57 Deg.F
1788636315	12.95 Volts	86.81 Deg.F
1788634519	12.95 Volts	85.05 Deg.F
1788630934	12.6 Volts	78.01 Deg.F
1788629141	12.69 Volts	78.01 Deg.F
1788627348	12.77 Volts	78.01 Deg.F

*Used Equation Coefficients:

Value1: 0, 0.0293, 0

Value2: 0, 0.88, -459.67

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)