KNAPPA-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object KNAPPA-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Value1*	Value2*	Value3*	Value4*	Value5*
1780898102	0.03	0	0.02	0	70
1780897442	0.11	0	0.05	0	70
1780896782	0.02	0	0.01	0	70
1780896122	0.15	0	0.08	0	70
1780895462	0.41	0	0.18	0	70
1780894803	0.99	0	0.51	0	71
1780894502	1.82	0	0.91	0	71
1780893842	7.99	0	3.5	0	72
1780893182	14.1	0	12.07	0	72
1780892522	14.07	0.02	14.25	0	73
1780891862	14.07	0.02	14.31	0	73
1780891203	14.12	0.03	14.33	0	73
1780890902	14.14	0.05	14.34	0.01	73
1780890242	14.17	0.15	14.36	0.07	73
1780889582	14.22	0.16	14.42	0.12	74
1780888922	14.24	0.2	14.44	0.15	74
1780888262	14.33	0.29	14.54	0.28	75
1780887603	14.47	0.47	14.61	0.41	75
1780887302	14.53	0.48	16.15	0.51	75
1780886642	22.32	0.94	53.15	1.55	76
1780885982	56.93	2.51	60.75	0.59	76
1780885322	58.66	2.48	60.63	0.57	77
1780884662	63.39	1.93	62.6	0.63	77
1780884003	67.69	3.64	65.16	0.76	77
1780883702	66.21	4.5	63.75	0.65	77

*Used Equation Coefficients:

Value1: 0, 1, 0

Value2: 0, 1, 0

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)