LY1LB-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object LY1LB-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1785281116	12.3 Volt	10 Pkt	38 Pcnt
1785280818	12.3 Volt	10 Pkt	36 Pcnt
1785280816	12.3 Volt	10 Pkt	36 Pcnt
1785280516	12.3 Volt	10 Pkt	33 Pcnt
1785280216	12.3 Volt	10 Pkt	36 Pcnt
1785279916	12.3 Volt	0 Pkt	34 Pcnt
1785279616	12.3 Volt	0 Pkt	22 Pcnt
1785279316	12.3 Volt	0 Pkt	18 Pcnt
1785279016	12.3 Volt	0 Pkt	16 Pcnt
1785278716	12.3 Volt	0 Pkt	14 Pcnt
1785278416	12.3 Volt	0 Pkt	14 Pcnt
1785278116	12.3 Volt	0 Pkt	15 Pcnt
1785277816	12.3 Volt	0 Pkt	14 Pcnt
1785277516	12.3 Volt	0 Pkt	17 Pcnt
1785277216	12.3 Volt	0 Pkt	14 Pcnt
1785276916	12.3 Volt	0 Pkt	12 Pcnt
1785276616	12.3 Volt	0 Pkt	12 Pcnt
1785276316	12.3 Volt	0 Pkt	12 Pcnt
1785276016	12.3 Volt	0 Pkt	9 Pcnt
1785275716	12.3 Volt	0 Pkt	8 Pcnt
1785275416	12.3 Volt	0 Pkt	8 Pcnt
1785275116	12.3 Volt	0 Pkt	8 Pcnt
1785274816	12.3 Volt	0 Pkt	8 Pcnt
1785274516	12.3 Volt	0 Pkt	5 Pcnt
1785274216	12.3 Volt	0 Pkt	4 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)