N9JY-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object N9JY-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Eff1h*	Eff*
1789931748	14.54 Volt	100 Pcnt	100 Pcnt
1789929946	14.54 Volt	100 Pcnt	100 Pcnt
1789928145	14.54 Volt	100 Pcnt	100 Pcnt
1789926349	14.54 Volt	100 Pcnt	100 Pcnt
1789924548	14.54 Volt	100 Pcnt	100 Pcnt
1789922739	14.54 Volt	100 Pcnt	100 Pcnt
1789920938	14.54 Volt	100 Pcnt	100 Pcnt
1789919136	14.54 Volt	100 Pcnt	100 Pcnt
1789917334	14.54 Volt	100 Pcnt	100 Pcnt
1789915532	14.54 Volt	100 Pcnt	100 Pcnt
1789913731	14.54 Volt	100 Pcnt	100 Pcnt
1789911929	14.54 Volt	100 Pcnt	100 Pcnt
1789910150	14.54 Volt	100 Pcnt	100 Pcnt
1789908326	14.54 Volt	100 Pcnt	100 Pcnt
1789906524	14.54 Volt	100 Pcnt	100 Pcnt
1789904722	14.54 Volt	100 Pcnt	100 Pcnt
1789902920	14.54 Volt	100 Pcnt	100 Pcnt
1789901119	14.54 Volt	100 Pcnt	100 Pcnt
1789899317	14.54 Volt	100 Pcnt	100 Pcnt
1789897515	14.54 Volt	100 Pcnt	100 Pcnt
1789895713	14.54 Volt	100 Pcnt	100 Pcnt
1789893912	14.54 Volt	100 Pcnt	100 Pcnt
1789892110	14.54 Volt	100 Pcnt	100 Pcnt
1789890308	14.54 Volt	100 Pcnt	100 Pcnt
1789888507	14.54 Volt	100 Pcnt	100 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.079, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Eff: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)