MKSRDG Telemetry

This is the latest recevied telemetry packets stored in our database for station/object MKSRDG. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1773050300	13.58 Volt	600 Pkt	82 Pcnt
1773050297	13.58 Volt	600 Pkt	82 Pcnt
1773049397	13.58 Volt	620 Pkt	82 Pcnt
1773048501	13.58 Volt	630 Pkt	81 Pcnt
1773048497	13.58 Volt	630 Pkt	81 Pcnt
1773047597	13.58 Volt	630 Pkt	80 Pcnt
1773046701	13.58 Volt	640 Pkt	81 Pcnt
1773046697	13.58 Volt	640 Pkt	81 Pcnt
1773045797	13.58 Volt	630 Pkt	78 Pcnt
1773044903	13.58 Volt	610 Pkt	78 Pcnt
1773044898	13.58 Volt	610 Pkt	78 Pcnt
1773043997	13.58 Volt	620 Pkt	78 Pcnt
1773043111	13.58 Volt	610 Pkt	78 Pcnt
1773043098	13.58 Volt	610 Pkt	78 Pcnt
1773042198	13.58 Volt	630 Pkt	80 Pcnt
1773041312	13.58 Volt	620 Pkt	80 Pcnt
1773041298	13.58 Volt	620 Pkt	80 Pcnt
1773040398	13.58 Volt	640 Pkt	82 Pcnt
1773039503	13.58 Volt	630 Pkt	81 Pcnt
1773039499	13.58 Volt	630 Pkt	81 Pcnt
1773038598	13.58 Volt	620 Pkt	81 Pcnt
1773037706	13.58 Volt	620 Pkt	81 Pcnt
1773037698	13.58 Volt	620 Pkt	81 Pcnt
1773036798	13.58 Volt	630 Pkt	79 Pcnt
1773035902	13.58 Volt	650 Pkt	78 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)