BG9EGA-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BG9EGA-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	CPUTemp*	DiGi*	Tx*	Rx*
1788570052	59 C	0 p	10 p	258 p
1788566452	59 C	0 p	9 p	194 p
1788562852	59 C	0 p	8 p	123 p
1788559252	60 C	0 p	7 p	98 p
1788555651	60 C	0 p	6 p	81 p
1788552051	61 C	0 p	5 p	65 p
1788548451	61 C	0 p	4 p	48 p
1788544851	62 C	0 p	3 p	31 p
1788541252	63 C	0 p	2 p	17 p
1788537652	65 C	0 p	1 p	1 p
1788534052	63 C	14 p	24 p	775 p
1788530452	63 C	14 p	23 p	759 p
1788526852	63 C	9 p	22 p	723 p
1788523251	63 C	0 p	21 p	652 p
1788519651	63 C	0 p	20 p	633 p
1788516051	63 C	0 p	19 p	597 p
1788512451	63 C	0 p	18 p	547 p
1788508852	62 C	0 p	17 p	528 p
1788505252	61 C	0 p	16 p	510 p
1788501652	60 C	0 p	15 p	488 p
1788498052	60 C	0 p	14 p	468 p
1788494452	60 C	0 p	13 p	388 p
1788490851	59 C	0 p	12 p	366 p
1788487251	58 C	0 p	11 p	345 p
1788483651	57 C	0 p	10 p	252 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

DiGi: 0, 1, 0

Tx: 0, 1, 0

Rx: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)