W6SRR-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object W6SRR-3. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	DC*	PC Board*	CPU*	Ambient*
1788693410	1353	72.2	30.6	64.5
1788692510	1351	72.4	30.6	64.8
1788691609	1356	72.5	30.6	64.5
1788690710	1353	72.6	31.1	64.6
1788689810	1351	72.7	30.6	64.8
1788688910	1353	73	31.1	65.4
1788688008	1353	73.1	31.1	65.1
1788687110	1353	73.2	31.1	65.3
1788686210	1351	73.3	31.1	65.5
1788685311	1353	73.6	31.6	66
1788684409	1353	73.6	31.1	65.8
1788683511	1353	73.7	32.2	65.9
1788682610	1353	74.1	32.2	66.3
1788681710	1349	74.1	31.6	66.2
1788680809	1354	74.2	31.1	66.3
1788679910	1353	74.4	32.2	67.1
1788679009	1354	74.6	31.6	66.5
1788678110	1353	74.6	32.2	66.8
1788677208	1349	75	32.2	67
1788676311	1353	75	32.2	67.1
1788675410	1353	75.2	32.7	67.6
1788674511	1349	75.3	32.2	67.3
1788673609	1353	75.5	32.2	68.1
1788672711	1353	75.8	32.2	67.7
1788671810	1354	75.9	32.2	68.1

*Used Equation Coefficients:

DC: 0, 1, 1000

PC Board: 0, 0.1, 0

CPU: 0, 0.1, 0

Ambient: 0, 0.1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)