DB0OHA-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DB0OHA-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1780543458	13.65 Volt	230 Pkt	87 Pcnt
1780543457	13.65 Volt	230 Pkt	87 Pcnt
1780542558	13.58 Volt	230 Pkt	87 Pcnt
1780542557	13.58 Volt	230 Pkt	87 Pcnt
1780541658	13.58 Volt	230 Pkt	85 Pcnt
1780541657	13.58 Volt	230 Pkt	85 Pcnt
1780540758	13.65 Volt	250 Pkt	85 Pcnt
1780540757	13.65 Volt	250 Pkt	85 Pcnt
1780539858	13.65 Volt	260 Pkt	85 Pcnt
1780539857	13.65 Volt	260 Pkt	85 Pcnt
1780538958	13.58 Volt	280 Pkt	85 Pcnt
1780538957	13.58 Volt	280 Pkt	85 Pcnt
1780538058	13.65 Volt	290 Pkt	85 Pcnt
1780538057	13.65 Volt	290 Pkt	85 Pcnt
1780537158	13.65 Volt	270 Pkt	86 Pcnt
1780537157	13.65 Volt	270 Pkt	86 Pcnt
1780536258	13.58 Volt	270 Pkt	84 Pcnt
1780536257	13.58 Volt	270 Pkt	84 Pcnt
1780535358	13.65 Volt	270 Pkt	87 Pcnt
1780535357	13.65 Volt	270 Pkt	87 Pcnt
1780534458	13.65 Volt	270 Pkt	87 Pcnt
1780534457	13.65 Volt	270 Pkt	87 Pcnt
1780533558	13.65 Volt	290 Pkt	89 Pcnt
1780533557	13.65 Volt	290 Pkt	89 Pcnt
1780532658	13.65 Volt	290 Pkt	92 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)