SR9WXL Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SR9WXL. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Rx10min*	Tx10min*	Digi10min*
1757410894	71 Pkt	5 Pkt	0 Pkt
1757410289	93 Pkt	9 Pkt	6 Pkt
1757409689	103 Pkt	13 Pkt	8 Pkt
1757409086	63 Pkt	6 Pkt	3 Pkt
1757408486	80 Pkt	8 Pkt	4 Pkt
1757407302	81 Pkt	5 Pkt	0 Pkt
1757406697	94 Pkt	4 Pkt	1 Pkt
1757406096	92 Pkt	5 Pkt	0 Pkt
1757405494	81 Pkt	3 Pkt	0 Pkt
1757404894	69 Pkt	4 Pkt	0 Pkt
1757403711	61 Pkt	6 Pkt	1 Pkt
1757403105	71 Pkt	3 Pkt	0 Pkt
1757401902	89 Pkt	3 Pkt	0 Pkt
1757401302	102 Pkt	6 Pkt	2 Pkt
1757400119	112 Pkt	5 Pkt	0 Pkt
1757399514	91 Pkt	5 Pkt	2 Pkt
1757398914	119 Pkt	5 Pkt	0 Pkt
1757397710	102 Pkt	4 Pkt	0 Pkt
1757396527	94 Pkt	5 Pkt	0 Pkt
1757395922	85 Pkt	3 Pkt	0 Pkt
1757395322	107 Pkt	5 Pkt	0 Pkt
1757394719	98 Pkt	3 Pkt	0 Pkt
1757394119	86 Pkt	4 Pkt	0 Pkt
1757392935	64 Pkt	5 Pkt	0 Pkt
1757392330	60 Pkt	3 Pkt	0 Pkt

*Used Equation Coefficients:

Rx10min: 0, 1, 0

Tx10min: 0, 1, 0

Digi10min: 0, 1, 0

HostTx10m: 0, 1, 0

Tempre: 0, 0.5, -50

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)