METMOR Telemetry

This is the latest recevied telemetry packets stored in our database for station/object METMOR. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1784671717	13.73 Volt	390 Pkt	65 Pcnt
1784671117	13.73 Volt	370 Pkt	67 Pcnt
1784670517	13.73 Volt	380 Pkt	67 Pcnt
1784669917	13.73 Volt	390 Pkt	69 Pcnt
1784669317	13.73 Volt	370 Pkt	69 Pcnt
1784668717	13.73 Volt	370 Pkt	68 Pcnt
1784668117	13.73 Volt	360 Pkt	70 Pcnt
1784667517	13.73 Volt	350 Pkt	71 Pcnt
1784666917	13.73 Volt	360 Pkt	72 Pcnt
1784666317	13.73 Volt	350 Pkt	71 Pcnt
1784665717	13.73 Volt	350 Pkt	70 Pcnt
1784665117	13.73 Volt	370 Pkt	72 Pcnt
1784664517	13.65 Volt	400 Pkt	73 Pcnt
1784663917	13.73 Volt	420 Pkt	72 Pcnt
1784663317	13.73 Volt	430 Pkt	74 Pcnt
1784662717	13.73 Volt	460 Pkt	76 Pcnt
1784662117	13.73 Volt	490 Pkt	77 Pcnt
1784661517	13.73 Volt	470 Pkt	77 Pcnt
1784660917	13.73 Volt	430 Pkt	76 Pcnt
1784660317	13.73 Volt	400 Pkt	76 Pcnt
1784659717	13.73 Volt	350 Pkt	74 Pcnt
1784659117	13.73 Volt	290 Pkt	70 Pcnt
1784658518	13.73 Volt	240 Pkt	67 Pcnt
1784657917	13.73 Volt	210 Pkt	69 Pcnt
1784657318	13.73 Volt	190 Pkt	67 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)