KC8SWY-15 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object KC8SWY-15. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Eff1h*	BarnT*
1780873372	12.6 Volt	25 Pcnt	72.5 F
1780873072	12.6 Volt	22 Pcnt	72.5 F
1780873072	12.6 Volt	22 Pcnt	72.5 F
1780872772	12.6 Volt	28 Pcnt	72.5 F
1780872472	12.6 Volt	33 Pcnt	72.5 F
1780872172	12.6 Volt	28 Pcnt	72.5 F
1780871872	12.6 Volt	22 Pcnt	72.5 F
1780871572	12.6 Volt	25 Pcnt	72.5 F
1780871273	12.6 Volt	25 Pcnt	72.5 F
1780871272	12.6 Volt	25 Pcnt	72.5 F
1780870972	12.6 Volt	25 Pcnt	72.5 F
1780870672	12.6 Volt	20 Pcnt	72.5 F
1780870372	12.6 Volt	22 Pcnt	72.5 F
1780870072	12.6 Volt	22 Pcnt	72.5 F
1780869772	12.53 Volt	25 Pcnt	72.5 F
1780869473	12.6 Volt	25 Pcnt	73.4 F
1780869472	12.6 Volt	25 Pcnt	73.4 F
1780869172	12.6 Volt	25 Pcnt	70.7 F
1780868872	12.6 Volt	22 Pcnt	70.7 F
1780868572	12.6 Volt	25 Pcnt	69.8 F
1780868272	12.6 Volt	28 Pcnt	69.8 F
1780867972	12.53 Volt	14 Pcnt	69.8 F
1780867673	12.6 Volt	12 Pcnt	71.6 F
1780867672	12.6 Volt	12 Pcnt	71.6 F
1780867372	12.6 Volt	12 Pcnt	72.5 F

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

BarnT: 0, 0.9, -83.2

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)