I1EPJ-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object I1EPJ-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1789977480	12.34 Volt	680 Pkt	86 Pcnt
1789977478	12.34 Volt	680 Pkt	86 Pcnt
1789976578	12.34 Volt	770 Pkt	87 Pcnt
1789975678	12.34 Volt	720 Pkt	87 Pcnt
1789974778	12.34 Volt	680 Pkt	87 Pcnt
1789973879	12.34 Volt	680 Pkt	87 Pcnt
1789973878	12.34 Volt	680 Pkt	87 Pcnt
1789972978	12.34 Volt	700 Pkt	87 Pcnt
1789972078	12.34 Volt	740 Pkt	87 Pcnt
1789971178	12.34 Volt	720 Pkt	88 Pcnt
1789970280	12.34 Volt	660 Pkt	86 Pcnt
1789970278	12.34 Volt	660 Pkt	86 Pcnt
1789969378	12.34 Volt	570 Pkt	86 Pcnt
1789968478	12.34 Volt	490 Pkt	84 Pcnt
1789967578	12.34 Volt	470 Pkt	83 Pcnt
1789966679	12.34 Volt	540 Pkt	85 Pcnt
1789966678	12.34 Volt	540 Pkt	85 Pcnt
1789965778	12.34 Volt	580 Pkt	85 Pcnt
1789964878	12.34 Volt	630 Pkt	85 Pcnt
1789963978	12.34 Volt	670 Pkt	87 Pcnt
1789963079	12.34 Volt	650 Pkt	86 Pcnt
1789963078	12.34 Volt	650 Pkt	86 Pcnt
1789962178	12.34 Volt	660 Pkt	88 Pcnt
1789961319	12.34 Volt	700 Pkt	89 Pcnt
1789960378	12.34 Volt	720 Pkt	90 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.073, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)