This is the latest recevied telemetry packets stored in our database for station/object YB2RX-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
Time
TX*
RX*
Digi*
V_Bat*
V_Ext*
1780599702
0 Count
26 Count
0 Count
0 VDC
0 VDC
1780597901
0 Count
24 Count
0 Count
0 VDC
0 VDC
1780596101
0 Count
21 Count
0 Count
0 VDC
0 VDC
1780590552
0 Count
21 Count
0 Count
0 VDC
0 VDC
1780589738
0 Count
21 Count
0 Count
0 VDC
0 VDC
1780587938
0 Count
18 Count
0 Count
0 VDC
0 VDC
1780586138
0 Count
15 Count
0 Count
0 VDC
0 VDC
1780584338
0 Count
13 Count
0 Count
0 VDC
0 VDC
1780583940
0 Count
13 Count
0 Count
0 VDC
0 VDC
1780582140
0 Count
10 Count
0 Count
0 VDC
0 VDC
1780580340
0 Count
6 Count
0 Count
0 VDC
0 VDC
1780578540
0 Count
4 Count
0 Count
0 VDC
0 VDC
1780576740
0 Count
1 Count
0 Count
0 VDC
0 VDC
1780574940
0 Count
0 Count
0 Count
0 VDC
0 VDC
1780574382
0 Count
0 Count
0 Count
0 VDC
0 VDC
1780572582
0 Count
0 Count
0 Count
0 VDC
0 VDC
1780570781
0 Count
0 Count
0 Count
0 VDC
0 VDC
1780568725
0 Count
0 Count
0 Count
0 VDC
0 VDC
*Used Equation Coefficients:
TX: 0, 1, 0
RX: 0, 1, 0
Digi: 0, 1, 0
V_Bat: 0, 0.01, 0
V_Ext: 0, 0.02, 0
The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0). The sent equation coefficients is used in the equation: a * value2 + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)