BV6BU-15 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BV6BU-15. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	CPUTemp*	RxPkts/20m*	RxPkts/1h*	RxPkts/24h*
1788597969	45.7 C	5 p	12 p	375 p
1788596769	47 C	4 p	10 p	372 p
1788595569	46.5 C	3 p	8 p	375 p
1788594369	44.9 C	3 p	9 p	377 p
1788593169	45.4 C	2 p	10 p	383 p
1788591969	46.2 C	4 p	11 p	388 p
1788590769	46.2 C	4 p	11 p	389 p
1788589569	46 C	3 p	10 p	391 p
1788588369	46.8 C	4 p	9 p	395 p
1788587169	46.4 C	3 p	9 p	395 p
1788585969	46.2 C	2 p	10 p	399 p
1788584768	46 C	4 p	10 p	402 p
1788583569	45.5 C	4 p	12 p	403 p
1788582369	47.4 C	2 p	11 p	405 p
1788581168	49.8 C	6 p	15 p	408 p
1788579969	49.2 C	3 p	16 p	404 p
1788578768	50.2 C	6 p	21 p	404 p
1788577569	49.2 C	7 p	19 p	403 p
1788576368	49.2 C	8 p	17 p	400 p
1788575169	50 C	4 p	14 p	398 p
1788573969	50.4 C	5 p	18 p	400 p
1788572769	48.8 C	5 p	18 p	401 p
1788571569	49.9 C	8 p	19 p	403 p
1788570369	49.7 C	5 p	16 p	401 p
1788569169	48.6 C	6 p	18 p	404 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/20m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)