IW0RED-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object IW0RED-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1788612112	13.13 Volt	630 Pkt	75 Pcnt
1788611812	13.13 Volt	630 Pkt	75 Pcnt
1788611512	13.2 Volt	620 Pkt	75 Pcnt
1788611212	13.2 Volt	630 Pkt	74 Pcnt
1788610912	13.2 Volt	630 Pkt	74 Pcnt
1788610612	13.05 Volt	630 Pkt	74 Pcnt
1788610312	13.2 Volt	610 Pkt	74 Pcnt
1788610012	13.05 Volt	560 Pkt	73 Pcnt
1788609713	13.05 Volt	520 Pkt	71 Pcnt
1788609412	13.05 Volt	520 Pkt	70 Pcnt
1788609112	13.13 Volt	520 Pkt	70 Pcnt
1788608812	13.13 Volt	520 Pkt	69 Pcnt
1788608512	13.2 Volt	520 Pkt	70 Pcnt
1788608212	13.2 Volt	530 Pkt	71 Pcnt
1788607912	13.13 Volt	530 Pkt	70 Pcnt
1788607613	13.13 Volt	530 Pkt	71 Pcnt
1788607312	13.2 Volt	510 Pkt	70 Pcnt
1788607013	13.13 Volt	520 Pkt	70 Pcnt
1788606713	13.2 Volt	530 Pkt	70 Pcnt
1788606413	13.2 Volt	540 Pkt	70 Pcnt
1788606113	13.2 Volt	540 Pkt	69 Pcnt
1788605813	13.2 Volt	560 Pkt	71 Pcnt
1788605513	13.13 Volt	570 Pkt	72 Pcnt
1788605213	13.2 Volt	600 Pkt	73 Pcnt
1788604913	13.05 Volt	610 Pkt	73 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)